![]() ![]() Soaking bathtubs are simple bathtubs without any massage function, whereas whirlpool bathtubs are equipped with water jets for hydrotherapy. What is the difference between a soaking tub and a whirlpool tub? The average lifespan of an acrylic bathtub is approximately 20 to 30 years. What is the average lifespan of a bathtub? For more details, follow this bathtub care guide. Using acids or chemicals for cleaning the bathtub can cause permanent damage to its surface. Acrylic bathtubs are easy to maintain and can be washed with regular soap. You may call our experts for any required assistance while purchasing our bathtub. No, Civil work is not required for installation of a freestanding bathtub. Yes, Freestanding bathtubs can be installed on top of tiles in an already constructed bathroom without the need of any civil work, they come with a flexible pipe that needs to connect in the floor drain.ĭo I need to Break or reconstruct my bathroom in order to install a bathtub? However, in the case of a fixed, drop-in bathtub, or spa tubs, civil work is required.Ĭan I install bathtub on a top of my bathroom tiles? Installation of a freestanding or a freestanding massage bathtub is an easy process that can be done by anyone. Our bathtubs are made from Premium Acrylic Sheets to ensure the smoothest feel on the skin and are reinforced with fiberglass to provide strength that lasts for decades.Ĭan I install a bathtub myself, or do I need professional help? You may also call our sales executive at 180 for any advice and suggestions while choosing a bathtub. To choose the right bathtub, consider factors such as the available space, bathroom layout, desired style, functionality, features, and personal preferences. ![]() How do I choose the right bathtub for my bathroom? ![]() To say that I'm looking forward to this is an understatement.right now it seems like it's all in the planning phase.- Our current catalogue consists of Acrylic fixed bathtubs, Acrylic Freestanding Bathtubs, Drop-in bathtubs, Jacuzzi bathtubs, Walk-in bathtubs, Spa tubs, and pools. Even better is, it's apparently held up (and rather strongly) by 2 bulkhead nuts, which means no siliconing fo a nice cleaner look. Saw someone's external box, made out of glass, attached by silicone, and got me googling boxes, and saw the reef savvy ghost overflow, and got to s 12 pieces of plastic, with 2 holes in 2 of the pieces, and 3 in another piece. ![]() Originally was going to do a quasi-coast to coast overflow, drill 3 holes, plumb it and go from there. Never done a build like this, so I'm in murky waters. IMO though if you have to ask if its even plausible you should just buy something pre-built. and some weld-on #4 (or 3) to weld it all together. (easily half the price of usplastics,etc. I don't know how strong bulkheads are, or which ones you plan to use, but unless the box is huge (and more specifically very wide making the lever bigger) it will probably be just fine.Ĭough. Some will be pulling the nut out (the lever aspect of the whole setup will pull on the top edge of the nut the most) but some will also be pushing into the tank wall (the bottom edge, which will most likely not go anywhere.). Most of the weight will not be on the nut, it will actually be on the bulkhead stem in shear. Thicker material than the internal wouldn't be bad either. Some internal bracing near the bulkheads would help, or having edges on the top side, or both. The internal box doesn't even need to be all that strong, but the external one does have to carry the plumbing (at least partially, it should be supported with clamps) and not tear off the wall (its a lever attached on a flat face). Especially without any teeth, which are bad anyway, nothing hard in the whole thing at all. It's fascinating that the only thing keeping that box attached are 2 bulkhead nuts.īuilding a couple of 5 sided boxes like that is very easy i think, its just simple cuts with some holes. The other question I have to ask is whether it would be cost effective to make it, or just wait and pay for it, though, I would change the hole design, from 2" to 1.5" bulkheads in the internal box, and 1" bulkheads in the external drain box. Basically, what you end up with is a big sandwich:īulkhead flange | gasket | internal overflow wall | gasket | tank wall | gasket | external overflow wall | bulkhead nutĭo you think it's plausible to make something similar? Instead of having teeth though, have say a 3/8" gap between water and a lid to provide a flat skimming area? Attaching an external box to the assembly as well would require yet another gasket, again between the tank and the box. But if there is a gasket between the box and the tank wall, then the seal remains solid. Acrylic 'bonding' is welding, and when done right its essentially one piece of acrylic, so definitely water tight. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |